Thermal Analyses on High and Medium Pressure Steam Flow in a Steam Conditioning Valve with a Steam Nozzle Using CFD

Helmisyah Ahmad Jalaludin; Muhammad Luqman  Muhamad Sharifuddin; Mohamad Ridzuan  Mohamed Rashid; Mohamad Zamin  Mohamad Jusoh

doi:10.24191/jaeds.v6i1.172

Authors

Helmisyah Ahmad Jalaludin Faculty of Mechanical Engineering, Universiti Teknologi MARA, Bukit Besi 23200 Terengganu, Malaysia.
Muhammad Luqman Muhamad Sharifuddin Faculty of Mechanical Engineering, Universiti Teknologi MARA, Bukit Besi 23200 Terengganu, Malaysia.
Mohamad Ridzuan Mohamed Rashid Faculty of Mechanical Engineering, Universiti Teknologi MARA, Bukit Besi 23200 Terengganu, Malaysia.
Mohamad Zamin Mohamad Jusoh Faculty of Mechanical Engineering, Universiti Teknologi MARA, Bukit Besi 23200 Terengganu, Malaysia.

DOI:

https://doi.org/10.24191/jaeds.v6i1.172

Keywords:

High Pressure; Steam Conditioning Valve; Hairline Crack; Computational Fluid Dynamics (CFD); Thermal Fatigue

Abstract

An essential part of controlling steam flow and pressure in industrial systems is a pressure control valve which lowers and regulates steam pressure prior to its delivery process. Unplanned plant shutdowns and large operating losses could cause damage like a hairline crack near a valve diffuser on the inside surface of the control valve caused by high pressure steam. Experienced in chemical industry, a pressure control valve located in a utility area has exhibited signs of internal surface cracking might due to continuous operation in high and medium pressure steam, whereby a valve replacement is needed. This study is exploratory and not intended for quantitative prediction with a scope involving modelling of steam conditioning valve using 3D modelling software. Based on the valve specifications, the study analysed the cause of hairline crack due to steam flow within the valve using Computational Fluid Dynamics (CFD) simulation with appropriate boundary conditions in determining temperature distribution along the inner surface. The objective was to investigate the effect of temperature distribution of the valve with and without a steam nozzle at Point A-B as the hairline crack area is predicted to be initiated based on real life occurrence. The impact of flow temperature in Steam Conditioning Valve contributing to the cracking event in valve body might be due to rapid expansion of high-pressure steam, which induces cooling due to energy conversion from internal energy to kinetic energy during compressible flow. By comparing high-pressure steam (HPS) and medium-pressure steam (MPS) conditions, the nozzle inlet’s pressure was reduced to compare the flow behaviour of valve under MPS condition. The overall temperature difference was significantly lower for MPS which is only 38% reduction compared with under HPS conditions of 59%. However, the temperature drop for HPS from Point A to B exhibited immediate drop compared to MPS condition which may cause cracking due to rapid cooling. The identification of critical regions with elevated temperature values, which can be related to the actual problem of chemical industry, may contribute to the ongoing MPS letdown of control valve replacement project in chemical industry.

Downloads

Download data is not yet available.

References

Galić, I., Vučković, K., Tonković, Z., & Čular, I. (2020). Numerical Simulation of Initiation and Crack Growth on Cast Valve Body. Engineering Failure Analysis, 117. https://doi.org/10.1016/j.engfailanal.2020.104793

Mo, Y., Zhang, C., Jin, B., & Chen, L. (2025). Simulation And Experiment of Static and Dynamic Characteristics of Pilot-Operated Proportional Pressure Reducing Valve. Flow Measurement and Instrumentation, 101.

Jalali, A., & Amiri Delouei, A. (2019). Failure Analysis in a Steam Turbine Stop Valve of a Thermal Power Plant. Engineering Failure Analysis, 105, 1131–1140. https://doi.org/10.1016/j.engfailanal.2019.07.057

Song, H., Huang, J., Gao, Y., Bao, Y., Zhang, S., Zhang, X., Bai, X., Ma, J., Li, D., & Wei, L. (2025). Numerical Analysis of Fluid Dynamics in a Novel 30 Mpa Back Pressure Valve with Dual Throttling Channels and a Spherical Valve Core. Flow Measurement and Instrumentation, 106. https://Doi.Org/10.1016/J.Flowmeasinst.2025.102944

Liu, F., Song, C., Pan, W., Wang, G., Zhang, H., Lei,Y., 2024. Thermal fatigue analysis of district heating pipeline under variable frequency regulation of circulating water pump, Applied Thermal Engineering, Vol. 242, 122535

Yang, L., Wang, Z., Dempster, W., Yu, X., & Tu, S. T. (2017). Experiments And Transient Simulation on Spring-Loaded Pressure Relief Valve Under High Temperature and High-Pressure Steam Conditions. Journal of Loss Prevention in the Process Industries, 45, 133–146.

American Petroleum Institute API 571, (2020). Damage Mechanism Affecting Fixed Equipment in the Refining Industry, Third Edition.

Du, C., Cui, H., & Zhang, H. (2025). Fatigue Fracture Behavior Under Thermal Cyclic Loads: Experimental Methods, Physical Regularities, And Damage Mechanisms. Engineering Failure Analysis, 174. https://doi.org/10.1016/j.engfailanal.2025.109508.

Quddus, A., Shah, A., Qureshi, K. R., Tahir, A., Basit, M. A. (2024). Numerical study on thermal hydraulics characteristics during steam submerged jet condensation from rectangular CD nozzle, Progress in Nuclear Energy, Vol. 168, 105048.

Panicker, N. S., Delchini, M. O. G., Sambor, T., Sabau, A. S. (2023). Computational fluid dynamics investigations of flow, heat transfer, and oxidation in heat recovery steam generator, Applied Thermal Engineering, Vol. 224, 120089.

Charton, H., Perret, C., & Phan, H. T. (2024). Analysis of Supersonic Flows inside a Steam Ejector with Liquid–Vapor Phase Change Using CFD Simulations. Thermo, 4(1), 1-15.

Al-Zahrani, A. (2024). “CFD Analysis for Improving Forced Convection Heat Transfer from Newly Designed Perforated Heat Sinks”, Eng. Technol. Appl. Sci. Res., vol. 14, no. 3, pp. 13883–13889.

Helmisyah, A. J., Omar, M. D. B., Seng., O. C., (2017). Characterisation of pressure and velocity of air flow through perforated pipe: Experimental and computational approach, e-Academia Journal, Vol. 6 (1), pp. 1-7.

Aziz, A. A. A. A., Abdullah, A. A., Jusoh, M. Z. M., Helmisyah, A. J., (2024). Performance of steam engine at different temperatures with various loads, Marine Frontier, Vol. 15, No. 2, 102-105.

Li, B., Li, C., Zheng, B., Yang, G., Wu, W., Li, W. and Cao, C. (2024) CFD simulation data report: Heat transfer coefficient and pressure drop of natural gas flow condensation in spiral tube. Front. Energy Res. 12:1376724. doi: 10.3389/fenrg.2024.1376724

España, R. E., Alvarez, L. V., Samarasinghe, J. T. (2025). Grid independence studies applied to a field-scale computational fluid dynamic (CFD) model using the detached eddy simulation (DES) technique along a reach of the Colorado River in Marble Canyon, Earth Surface Processes and Landforms, Vol. 50(3), DOI: 10.1002/esp.70030

Tawackolian, K., and Kriegel, M., (2023). Validation of computational fluid dynamics simulations for determining pressure loss coefficients of ventilation components, Building Services Engineering Research & Technology, Vol. 44(3), https://doi.org/10.1177/01436244231159537

Shabani, S., Majkut, M., Dykas, S., Smolka, K., Lakzian, E., and Zhang, G., (2023). Validation of the CFD Tools against In-House Experiments for Predicting Condensing Steam Flows in Nozzles, Energies, 16(12), 4690; https://doi.org/10.3390/en16124690